Product category
  • Servos
    Micro Servo
    MiNi Servo
    Wing Servo
    Low Profile Servo
    Helicopter
    Standard Servo
    Large Size Servo
  • Electronic speed controller
    ESC
    ESC Part
  • Motors
  • Gyro
  • RC Accessories
    Metal servo Arm
    Cooling Fan & Heatsink
    Wire & Connectors
  • Screw & Plug
    Screw set
    Button Head Screw
    M2
    M3
    M4
    Flat Head Screw
    M2
    M3
    M4
    Cap Head Screw
    M3
    Connector
Product description

Product description

副标题

Collection
|
|
OMG-GYRO-V4 
Price:
$49.00
Weight:g: 12
Size:mm: 25x26x10
Color:
Stock:
90
Quantity:
Spec. & Description
Product comment(0)

V4 3-AXIS Gyro for Drift car and Touring Drift F1

1.Working voltage: 5V-8.4V

2.Consumption current: 6V 20mA≤

3.Support input signal: PWM(50-333Hz)/FUTABA S.BUS/SANWA SSR/SANWA SHR

4.Output servo signal: 1520uS(333Hz)/760uS(FUTABA SR)/SANWA SSR

Control system: PID control system

5.End Point Adjustment Function:EPA

6.Control Signal:SBUS/PWM

7.Receiver type:No restriction


V4 3-AXIS Gyro for Drift car and Touring Drift F1

Working voltage: 5~ 8.4V

Consumption current:   6V   20mA≤

Working temperature: -10 ℃ + 50

Support input signal: PWM(50-333Hz)/FUTABA S.BUS/SANWA SSR/SANWA SHR

Output servo signal:   1520uS(333Hz)/760uS(FUTABA SR)/SANWA SSR

Control system: PID control system

End Point Adjustment Function:EPA

Control Signal:SBUS/PWM

Receiver type:No restriction

Dimension: 25*26*10mm  

Weight: 12g  


Instruction of Function Switch

1.EPA(Travel Setting)

Press the "SW" switch to power on,yellow LED blinks slowly.Entering to the servo travel setting,rotate the remote control steering wheel to make servo stop at the desired position(turn left/turn right).Short press"SW" switch,yellow LED blinks 2 times quickly,red LED becomes solid,and green LED blinks slowly,it means current travel has been saved.Then rotate the remote control steering wheel to make the servo stop at the other desired position,short press the switch ,yellow LED blinks 2 times quickly,and then the yellow LED turns on,it means current travel has been saved as well.2 seconds later,the gyro will automatically enter into initialization mode,once completed,gyro is ready for use.

2.Reset(Travel Restore Default Setting)

Press the "SW" switch to power on and enter into the travel setting mode.After pressing and holding the switch for 3 seconds,the yellow LED starts to blinks alternately.Restore to default after 2 seconds. Then it will enter into initialization mode,once initialization is completed,the gyro is ready for use.

3.Gain signal input or potentiometer adjustment is determined when the power is turned on. If loss of signal happened during using,the last signal is retained.

4.Suitable for most of remote control systems,while plug in the gain wwire,it can adjust the sensitivity by transmitter;while do not plug in the gain wire,the gyro's potentiometer can be used for gain adjustment.

5.Suitable for FUTABE S.BUS & SANWA SSR

6.Adjust the gain via gain channel of transmitter(default for S.BUS input),the range if from -100%~0~+100%.

7.While do not plug in the gain wire,the gyro's potentiometer can be used for gain adjustment,range from 0~100%.

8.After powering on,press the SW for a while,LED2 flash(next to the SW),then short press the SW,and choose the direction of the X/Y/Z axis.


LED Status Display

3Axis LEDStatus

Red quick flash            Initialization

Yellow quick flash        Loss of control signal

Green solid light          Small gain mode/Gain signal input

Green slow flash          Small gain mode/Potentiometer adjustment

Blue solid light             Big gain mode/Gain signal input

Blue slow flash             Big gain mode/Potentiometer adjustment

Yellow slow flash          Travel set mode